Message from
Chairman of Central Boilers Board


About Central Boilers
Board


History of Indian Boiler Regulations

Foreword

Contents Chapter
Wise


Contents Regulation
Wise


List of Amendments

Indian Boilers
Act 1923


Ibr Forms

Home

Search

Help

Contact Us

CHAPTER : II

Reg.9 Process of manufacture
Reg.10 Chemical Analysis
Reg.11 Freedom from defects, etc
Reg.12 Rolling Margin
Reg.13 Testing and Inspecting.
Reg.13A Designate steel
Reg.14 Selection of test pieces
Reg.15 Tensile Test pieces
Reg.16 Tensile tests
Reg.17 Number of Tensile Tests
Reg.18 Dump Tests
Reg.19 Bend Tests
Reg.20 Number of Bend Tests
Reg.21 Manufactured Rivets
Reg.22 Additional tests before rejection
Reg.23 Branding
Reg.24 Defacing of rejected material
Reg.25 Facilities for inspection
Reg.26 Steel not produced where rolled
Reg.27 Maker’s Certificate
Reg.28 Rivet Bars
Reg.29 Manufactured Rivets Tests
Reg.30 Stay Bars
Reg.31 Stay Bars - Bend Tests
Reg.32 Special Iron for Screw Stays for Fire-boxes and Combustion Chambers
Reg.33 Plates
Reg.34 Stay and Rivet bars
Reg.35-1 Copper Tubes
Reg.35-2 Brass Tubes
Reg.35-3 Carbon steel tubes
Reg.36 Material process
Reg.37 Selection of Tubes for Test
Reg.38 Tensile strength
Reg.39 Flattening Test
Reg.40 Flanging and drift expanding test
Reg.41 Additional test before rejection
Reg.42 Hydraulic Test
Reg.43 Material
Reg.44 Tensile strength
Reg.45 Additional tests before rejection
Reg.46 Hydraulic Test
Reg.47 General
Reg.48 Material
Reg.49 Tensile Test
Reg.49B Flattering Test
Reg.49C Expanding  Test
Reg.50 Additional tests before rejection
Reg.51 Hydraulic test.
Reg.52 General
Reg.53 a Material
Reg.53 b Heat treatment
Reg.53 c Workmanship and tolerance
Reg.53 d Selection of Tubes for testing
Reg.54 a Tensile Test
Reg.54 b Flattening Test
Reg.54 c Expanding Tests
Reg.55 Additional tests before rejection
Reg.56 Hydraulic Test
Reg.56A Seamless Chromium
Reg.57 General
Reg.58 Material
Reg.59 Flattening test
Reg.60 Tensile Test
Reg.61 Hydraulic test
Reg.62 Test specimens
Reg.63 Number of tests
Reg.63A Cold Drawon Electric
Reg.73 Scope
Reg.74 Process of manufacture
Reg.75 Freedom from all rectification of defects
Reg.76 Number of tests
Reg.77 Tensile Test
Reg.78 Bend tests
Reg.79 Additional tests before rejection
Reg.80 Procedure for Welding
Reg.81 Forged or rolled pressure parts
Reg.82 Selection of test pieces
Reg.83 Tensile strength
Reg.84 Bend Tests
Reg.85 Additional tests before rejection
Reg.86 General grey iron casting (Grade A)
Reg.87 Provision of test bars
Reg.88 Dimension of test bars
Reg.89 Mechanical test
Reg.90 Transverse test
Reg.91 Tensile test
Reg.92 Number of transverse and tensile tests
Reg.93 Additional Tests
Reg.94 General requirements
Reg.95 Requirements for Normal Penetration Electrodes
Reg.96 Requirements for Deep Penetration Butt-Welding Electrodes
Reg.97 Requirements for Deep Penetration Fillet Welding Electrodes
Reg.98 Periodic Check Test
Reg.98A Filler rods for gas welding of steel

 
Back   Top
Message from Chairman of Central Boilers Board About Central Boiler Board History of Indian Boiler Regulations Foreword Contents Chapter Wise Contents Regulation Wise List of Amendments
Indian Boilers Act 1923 Ibr Forms Home Search Help Contact Us